blob: 8972881505ed934518a8e6ecdb15d6985e2cce47 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
|
#
# Copyright (c) 2021 Polarity Works
# SPDX-License-Identifier: MIT
#
CONFIG_SOC_SERIES_NRF52X=y
CONFIG_SOC_NRF52840_QIAA=y
CONFIG_BOARD_ADV360_LEFT=y
CONFIG_ZMK_SPLIT=y
CONFIG_ZMK_SPLIT_BLE=y
CONFIG_ZMK_SPLIT_BLE_ROLE_CENTRAL=y
# Enable MPU
CONFIG_ARM_MPU=y
# enable GPIO
CONFIG_GPIO=y
# Enable SPI
CONFIG_SPI=y
CONFIG_SPI_NRFX=y
# Enable writing to flash
CONFIG_USE_DT_CODE_PARTITION=y
CONFIG_MPU_ALLOW_FLASH_WRITE=y
CONFIG_NVS=y
CONFIG_SETTINGS_NVS=y
CONFIG_FLASH=y
CONFIG_FLASH_PAGE_LAYOUT=y
CONFIG_FLASH_MAP=y
# Enable 32kHz crystal
CONFIG_CLOCK_CONTROL_NRF_K32SRC_XTAL=y
CONFIG_CLOCK_CONTROL_NRF_K32SRC_30PPM=y
CONFIG_ZMK_RGB_UNDERGLOW=y
CONFIG_ZMK_RGB_UNDERGLOW_EXT_POWER=y
CONFIG_ZMK_RGB_UNDERGLOW_ON_START=y
CONFIG_ZMK_RGB_UNDERGLOW_EFF_START=4
CONFIG_ZMK_RGB_UNDERGLOW_AUTO_OFF_IDLE=y
# Use the STRIP config specific to the LEDs you're using
CONFIG_WS2812_STRIP=y
CONFIG_BT_CTLR_TX_PWR_PLUS_8=y
CONFIG_PWM=y
CONFIG_ZMK_LED_PWM=y
CONFIG_ZMK_BACKLIGHT=y
CONFIG_ZMK_BACKLIGHT_BRT_START=20
CONFIG_ZMK_BACKLIGHT_AUTO_OFF_IDLE=y
CONFIG_ZMK_HID_REPORT_TYPE_NKRO=y
CONFIG_ZMK_HID_CONSUMER_REPORT_USAGES_BASIC=y
# Turn on logging, and set ZMK logging to debug output
CONFIG_LOG=y
CONFIG_ZMK_USB_LOGGING=y
CONFIG_ZMK_LOG_LEVEL_DBG=y
CONFIG_LOG_BUFFER_SIZE=65536
CONFIG_LOG_STRDUP_BUF_COUNT=160
#CONFIG_I2C_LOG_LEVEL_DBG=y
#CONFIG_SPI_LOG_LEVEL_DBG=y
# Turn on USB CDC ACM device
CONFIG_USB=y
CONFIG_USB_DEVICE_STACK=y
CONFIG_USB_CDC_ACM=y
CONFIG_USB_CDC_ACM_RINGBUF_SIZE=1024
CONFIG_USB_CDC_ACM_DEVICE_NAME="CDC_ACM"
CONFIG_USB_CDC_ACM_DEVICE_COUNT=1
# Enable serial console
CONFIG_SERIAL=y
CONFIG_CONSOLE=y
CONFIG_UART_INTERRUPT_DRIVEN=y
CONFIG_UART_LINE_CTRL=y
# Enable USB UART, and set the console device
CONFIG_UART_CONSOLE=y
CONFIG_USB_UART_CONSOLE=y
CONFIG_UART_CONSOLE_ON_DEV_NAME="CDC_ACM_0"
|
