1 files changed, 84 insertions, 0 deletions
diff --git a/config/boards/arm/adv360/adv360_left_defconfig b/config/boards/arm/adv360/adv360_left_defconfig
new file mode 100644
index 0000000..8972881
--- /dev/null
+++ b/config/boards/arm/adv360/adv360_left_defconfig
@@ -0,0 +1,84 @@
+#
+# Copyright (c) 2021 Polarity Works
+# SPDX-License-Identifier: MIT
+#
+
+CONFIG_SOC_SERIES_NRF52X=y
+CONFIG_SOC_NRF52840_QIAA=y
+CONFIG_BOARD_ADV360_LEFT=y
+CONFIG_ZMK_SPLIT=y
+CONFIG_ZMK_SPLIT_BLE=y
+CONFIG_ZMK_SPLIT_BLE_ROLE_CENTRAL=y
+
+# Enable MPU
+CONFIG_ARM_MPU=y
+
+# enable GPIO
+CONFIG_GPIO=y
+
+
+# Enable SPI
+CONFIG_SPI=y
+
+CONFIG_SPI_NRFX=y
+
+# Enable writing to flash
+CONFIG_USE_DT_CODE_PARTITION=y
+CONFIG_MPU_ALLOW_FLASH_WRITE=y
+CONFIG_NVS=y
+CONFIG_SETTINGS_NVS=y
+CONFIG_FLASH=y
+CONFIG_FLASH_PAGE_LAYOUT=y
+CONFIG_FLASH_MAP=y
+
+# Enable 32kHz crystal
+CONFIG_CLOCK_CONTROL_NRF_K32SRC_XTAL=y
+CONFIG_CLOCK_CONTROL_NRF_K32SRC_30PPM=y
+
+CONFIG_ZMK_RGB_UNDERGLOW=y
+CONFIG_ZMK_RGB_UNDERGLOW_EXT_POWER=y
+CONFIG_ZMK_RGB_UNDERGLOW_ON_START=y
+CONFIG_ZMK_RGB_UNDERGLOW_EFF_START=4
+CONFIG_ZMK_RGB_UNDERGLOW_AUTO_OFF_IDLE=y
+
+# Use the STRIP config specific to the LEDs you're using
+CONFIG_WS2812_STRIP=y
+CONFIG_BT_CTLR_TX_PWR_PLUS_8=y
+CONFIG_PWM=y
+CONFIG_ZMK_LED_PWM=y
+CONFIG_ZMK_BACKLIGHT=y
+CONFIG_ZMK_BACKLIGHT_BRT_START=20
+CONFIG_ZMK_BACKLIGHT_AUTO_OFF_IDLE=y
+
+CONFIG_ZMK_HID_REPORT_TYPE_NKRO=y
+CONFIG_ZMK_HID_CONSUMER_REPORT_USAGES_BASIC=y
+
+
+# Turn on logging, and set ZMK logging to debug output
+CONFIG_LOG=y
+CONFIG_ZMK_USB_LOGGING=y
+CONFIG_ZMK_LOG_LEVEL_DBG=y
+CONFIG_LOG_BUFFER_SIZE=65536
+CONFIG_LOG_STRDUP_BUF_COUNT=160
+#CONFIG_I2C_LOG_LEVEL_DBG=y
+#CONFIG_SPI_LOG_LEVEL_DBG=y
+
+
+# Turn on USB CDC ACM device
+CONFIG_USB=y
+CONFIG_USB_DEVICE_STACK=y
+CONFIG_USB_CDC_ACM=y
+CONFIG_USB_CDC_ACM_RINGBUF_SIZE=1024
+CONFIG_USB_CDC_ACM_DEVICE_NAME="CDC_ACM"
+CONFIG_USB_CDC_ACM_DEVICE_COUNT=1
+
+# Enable serial console
+CONFIG_SERIAL=y
+CONFIG_CONSOLE=y
+CONFIG_UART_INTERRUPT_DRIVEN=y
+CONFIG_UART_LINE_CTRL=y
+
+# Enable USB UART, and set the console device
+CONFIG_UART_CONSOLE=y
+CONFIG_USB_UART_CONSOLE=y
+CONFIG_UART_CONSOLE_ON_DEV_NAME="CDC_ACM_0"